Posted: Wed Mar 14, 2007 2:06 pm Post subject: X3 pinheader question
the adapter i have for my X3 is a X-addon. it has every pin...now, i took of pin 16 because that hole is blank on the X3 chip, but i do also know that pin 4 is not in use...do i need to take that one off also or can i just leave it? its not blanked on the chip, but i didnt know if i left it, it would mess the chip up or anything?
thanks...got my control panel and x3 chip...just got to get it all put in tonight.
stud_man50 Xbox-HQ Freak Xbox Version: 1.4 Modded: Xecuter3CE
Joined: Feb 20, 2006 Posts: 808 Location: MI, USA
Posted: Wed Mar 14, 2007 9:31 pm Post subject:
why are you trying to use a smartxx adapter for an X3? try an Xapt3r.. _________________ (2) XBOX v1.4:
Xecuter3CE Modchip
X3 3294 Bios
250GB Seagate HDD
XBMC Dashboard
Disclaimer: It is my intention to give the best possible advice to all forum users. However should my advice fail to be of a reasonble standard I cannot be held liable for any loss or damage caused. To act on any advice given without contemplating the consequences shows stupidity and ignorance on your behalf.
joho5 Xbox-HQ Freak
Joined: Jan 22, 2007 Posts: 699 Location: Texas
Posted: Wed Mar 14, 2007 9:55 pm Post subject:
stud_man50 wrote:
why are you trying to use a smartxx adapter for an X3? try an Xapt3r..
the place i bought the chip from was out...and this one has been used with the X3.
they linked me to a tut on using this adaptor with the X3 chip. that hole on the adaptor has no power or anything going to it.
the d0 setup on this adaptor is alot more install-friendly. it requires no shaping or bending, etc...
stud_man50 Xbox-HQ Freak Xbox Version: 1.4 Modded: Xecuter3CE
Joined: Feb 20, 2006 Posts: 808 Location: MI, USA
Posted: Thu Mar 15, 2007 3:13 am Post subject:
then if you have a tut and its been used on an X3 whats your question then, LOL _________________ (2) XBOX v1.4:
Xecuter3CE Modchip
X3 3294 Bios
250GB Seagate HDD
XBMC Dashboard
Disclaimer: It is my intention to give the best possible advice to all forum users. However should my advice fail to be of a reasonble standard I cannot be held liable for any loss or damage caused. To act on any advice given without contemplating the consequences shows stupidity and ignorance on your behalf.
roo465 Moderator
Joined: Apr 29, 2005 Posts: 982 Location: ACT, Australia
Posted: Thu Mar 15, 2007 8:19 am Post subject:
To answer your question: when doing the pinheader install, you remove pins 4 and 16 from the pinheader. So I see no problem with removing it from your solderless adapter.
So pull both 4 and 16, and you will be fine _________________
joho5 Xbox-HQ Freak
Joined: Jan 22, 2007 Posts: 699 Location: Texas
Posted: Thu Mar 15, 2007 1:52 pm Post subject:
i just moved 16 and left 4, because i noticed on the adapter that pin 4 isnt connected or linked to anything anyways.
i was asking because i dont have the net out at my house in the BOON DOCKS (we moved recently) and i want to be clear of everything when i go to do the install. it all worked out good though, just had simple bios flashing problem.
my chip will only allow flashing when the light is red on the chip, not green. its flipped. if i try to flash it when its green...it says unknown flash, halting.
weird.
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 8,746 | 
Guests: 1226 | 
Members: 2 
Forums 
