Posted: Sat Aug 26, 2006 5:01 am Post subject: hyperx problems
Hey,
i just got the mod chip and i've got it installed in my 1.3 xbox and the chip blinks green while my xbox blinks red/green, i think it might be a problem with the LPC but i'm not sure since i dont have as m uch knowledge as all of you guys.
please reply
thanks
Greven Xbox-Hq Genius Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Jan 19, 2006 Posts: 2755 Location: Calgary, Alberta, Canada
Posted: Sat Aug 26, 2006 5:11 am Post subject:
If you turn the chip off does the xbox boot normal?
It sounds like you may need to flash the bios as well. Any video output?
Well red and green means it fraging _________________
brendan721 Xbox-HQ Enthusiast
Joined: Aug 19, 2006 Posts: 22
Posted: Sat Aug 26, 2006 3:47 pm Post subject:
yea when i turn it off it boots just fine, no video output when i turn the chip on though. everythings connected, i've checked the connections many many times. so could you please teach how to flash this bios.
thanks alot
Greven Xbox-Hq Genius Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Jan 19, 2006 Posts: 2755 Location: Calgary, Alberta, Canada
Posted: Sat Aug 26, 2006 4:21 pm Post subject:
From what I understand about the Hyperx(realhypnotx, wanna comment?) it should be pre-flashed with FlashBios, cause I don't beleive that there is a programmer for this chip.
So, assuming it's pre-flashed, it means that there is something wrong with the chip.
did you follow this? I would try to reinstall if you can and check that all the connections are firm. _________________ Hotswap|HDD Upgrade|X3 Guide
brendan721 Xbox-HQ Enthusiast
Joined: Aug 19, 2006 Posts: 22
Posted: Sat Aug 26, 2006 4:29 pm Post subject:
yea i followed that completely, i'll just reinstall it again
brendan721 Xbox-HQ Enthusiast
Joined: Aug 19, 2006 Posts: 22
Posted: Sat Aug 26, 2006 6:12 pm Post subject:
i reinstalled the chip, and this time i ran a wire from the d0 point from the bottom and then just connected it to the "E" wire and and the chip still blinks green while the xbox blinks red and green. when the switch is off i get full access to the xbox
Greven Xbox-Hq Genius Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Jan 19, 2006 Posts: 2755 Location: Calgary, Alberta, Canada
Posted: Sat Aug 26, 2006 6:32 pm Post subject:
Definitely somethign with the chip. Your D0 is fine if you have problems when the chip is on. If the D0 was the issue, it wouldn't affect the xbox at all.
So if it frags its a something with the chip or the solderless adapter. Do all the pogo pins sit properly in the hole? We had another member with this problem.
Just so everyone knows, hyperx chips are the same chips as spider, just under a different name. _________________ Hotswap|HDD Upgrade|X3 Guide
brendan721 Xbox-HQ Enthusiast
Joined: Aug 19, 2006 Posts: 22
Posted: Sat Aug 26, 2006 7:09 pm Post subject:
what do you mean by sit properly in the hole, i only used the E wire and the rest aren't being used, but i haven't cut them off and they aren't touching each other
brendan721 Xbox-HQ Enthusiast
Joined: Aug 19, 2006 Posts: 22
Posted: Sat Aug 26, 2006 7:24 pm Post subject:
my xbox version is a 1.3 so i thought all i need to do is put just the e pin in the d0 point.
TheRealHypnotiX Moderator
Joined: Feb 01, 2006 Posts: 2508 Location: Pensacola, FL
Posted: Mon Aug 28, 2006 6:00 am Post subject:
yes just E and also, this chip was cheaply made, i had to rig it in a gay way to make it work. It does come with flash bios use htis tutorial by me to flash it Tutorial......now, if its still fragging, make sure all the pins are in the whole and none of the pins are sticking beacause that was my problem, i just soldered a piece of wire to the stuck pin, put the chip in, cut the wire where it needed to be(almost even with the mobo) and soldered it, sumtimes it wont turn on and i just pres it down and it works, wich is y i am in need of a better chip!!!! In my opinion, htis chip is garbage!!! PM me if u need any more help with it tho
Joined: Feb 01, 2006 Posts: 2508 Location: Pensacola, FL
Posted: Mon Aug 28, 2006 6:02 am Post subject:
Greven wrote:
Definitely somethign with the chip. Your D0 is fine if you have problems when the chip is on. If the D0 was the issue, it wouldn't affect the xbox at all.
So if it frags its a something with the chip or the solderless adapter. Do all the pogo pins sit properly in the hole? We had another member with this problem.
Just so everyone knows, hyperx chips are the same chips as spider, just under a different name.
oh, the pins dont sit in the lpc, and i can't figure out a way to make them sit properly without buying a 30 dollar adaptor, the pins just dont even line up with the lpc so i had to make the hole on the chip bigger and clamp it to the motherboard, but it still isn't fully connecting
TheRealHypnotiX Moderator
Joined: Feb 01, 2006 Posts: 2508 Location: Pensacola, FL
Posted: Mon Aug 28, 2006 4:08 pm Post subject:
well as i said mine was the same plus 1 pin was stuck so i soldered a wire down in the LPC hole for the stuck 1 and it worked, but still sumtimes i have to press down on the chip, leave the washer off, it wont touch the board if its on, and last but not least, i also had to kind of MAKE it fit its weird, just play with it a bit!!! need any more help please please post!!!! _________________ Hotswap Tutorial|FTP Tutorial|HyperX Flashing Tutorial
hellblazer55 V.I.P. Lifetime
Joined: Oct 03, 2005 Posts: 6381 Location: Canada
Posted: Mon Aug 28, 2006 8:30 pm Post subject:
get the solderless xapter, its better quality than what the one your provided with the hyperX _________________
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 9,457 | 
Guests: 1517 | 
Members: 2 
Forums 
