Joined: Dec 09, 2004 Posts: 19 Location: Ohio, USA
Posted: Wed Dec 15, 2004 4:40 am Post subject: Xenium ICE problems
when i was figuring out what version xbox i had i found out that mine was either a 1.4 or 1.5 and that 1.5 were made in August of 2003 and then microsoft went back to 1.4 before 1.6. Becuase of this i figured i had a 1.4 since mine was manufactured in November. I just installed my chip however.....and i'm almost positive i did everything right but nothing happened. Even though mine was made in November is there a chance that its a 1.5 and i have to solder those couple of wires?
TheModGod Xbox-Hq Legendary Xbox Version: V1.4 Modded: Xenium Ice
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Wed Dec 15, 2004 5:10 am Post subject:
Yes, you have a 1.5 most likely.
The only true way to determine (that I know of) is to check for continuity between the number 2 LPC Hole and ground. If you have continuity you have a 1.4 if not you have a 1.5.
The 1.5 machine is very scarce, but it is out there. If you are certain you did everything right and you have NO LED on the chip then I would mod it like a 1.5.
Let me know if you get joy.
TheModGod
---------------------------
http://www.xbox-hq.com http://www.themodgod.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
tsuwr927 Xbox-HQ User
Xbox Version: V1.4 Modded: Xenium Ice
Joined: Dec 09, 2004 Posts: 19 Location: Ohio, USA
Posted: Wed Dec 15, 2004 5:17 am Post subject:
i have an LED but it doesn't light up at all
TheModGod Xbox-Hq Legendary Xbox Version: V1.4 Modded: Xenium Ice
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Wed Dec 15, 2004 5:22 am Post subject:
Every Xenium Ice mod chip has an LED on it.
I would say to mod it like a 1.5
It won't hurt. The same thing happened to me once. I chipped a machine that I thought was a 1.4 and I had nothing. I popped the two extra wires on there and viola, it worked.
TheModGod
----------------------------
http://www.xbox-hq.com http://www.themodgod.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
tsuwr927 Xbox-HQ User
Xbox Version: V1.4 Modded: Xenium Ice
Joined: Dec 09, 2004 Posts: 19 Location: Ohio, USA
Posted: Wed Dec 15, 2004 5:28 am Post subject:
ok i can do that. but what if i had done something wrong and it is a 1.4 and i mod it like a 1.5......will it harm anything? and i put the chip in with a solderless adapter, can solder the ground wire and the 3.3 wire to that or will i have to take it out and just solder everything? and thanks for taking the time to help me with this
TheModGod Xbox-Hq Legendary Xbox Version: V1.4 Modded: Xenium Ice
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Wed Dec 15, 2004 6:16 am Post subject:
What is soldered can always be undone, so I would have to say that if it was a dead chip issue or something like that then you would be okay.
I personally have never used any solderless adapters so I can't answer that other questions. I always solder a pin header and go from there. But, i would imagine that you could still solder to the adapter, I think it was the number 2 pin...heck, I have only done 1 1.5 so far so I can't remember.
Since everything is done on the top I would say that you would solder to the adapter. Just make sure you have desoldering braid to take it back to normal if you have to.
TheModGod
----------------------------
http://www.xbox-hq.com http://www.themodgod.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
tsuwr927 Xbox-HQ User
Xbox Version: V1.4 Modded: Xenium Ice
Joined: Dec 09, 2004 Posts: 19 Location: Ohio, USA
Posted: Wed Dec 15, 2004 6:24 am Post subject:
ok....thanks for your help
TheModGod Xbox-Hq Legendary Xbox Version: V1.4 Modded: Xenium Ice
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Wed Dec 15, 2004 8:59 pm Post subject:
Let me know how it goes! _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
custom-xmodz Xbox-HQ Freak
Joined: Aug 28, 2004 Posts: 796 Location: Wales, UK
Posted: Thu Dec 16, 2004 7:03 am Post subject:
Ive had a fair few 1.5 xbox's, if ti was me I would just solder it in, takes out any possible issues with the solderless adapter then
DJH
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum