Posted: Mon May 02, 2005 9:39 pm Post subject: Xenium ICE Problems
Using the FAQ here and from a few other places I managed to install a Xenium ICE mod.
However: The red LED flickers on and off (as does the XBOX power LED) until stabilizing to a point where the LED is on, and the XBOX power LED flashes red and green. No signal to the TV, though.
Anyone got any suggestions?
TheModGod Xbox-Hq Legendary
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Mon May 02, 2005 9:59 pm Post subject:
Did you solder? Did you use solderless install?
Is your machine a 1.6 version, Is it a 1.5 version, or is it one of the others?
The more info you give us the more help we can give you. Right now I don't know whether to tell you that you need to check your LPC Rebuild, your pin header, your solderless adapter, or to tell you that you have a bad chip.
TheModGod
-------------------------
http://www.themodgod.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Mon May 02, 2005 11:21 pm Post subject:
Sorry. 1.4 XBOX, solderless.
Drago912 Xbox-HQ Member
Joined: Feb 15, 2005 Posts: 57 Location: Canada
Posted: Tue May 03, 2005 1:26 am Post subject:
So you couldnt get it to boot to the Xenium os screen? Are you sure you place the DO from the solderless adapter at the right point on the mobo?
TheModGod Xbox-Hq Legendary
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Tue May 03, 2005 2:37 am Post subject:
Yes, check your D0 also check the alignmetn of the chip. The one thing you MUST be careful with is the solderless adapters have very sharp pogo pins on them. If you widdle that puppy around too much you can scratch a trace and create damage to the motherboard.
I have actually seen more people do damage with solderless adapters than soldering.
If you are certain all is well with chip alignment and D0, then I would say your chip is bad.
TheModGod
------------------------
http://www.themodgod.com _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Wed May 04, 2005 3:48 am Post subject:
It just gives me nothing. I'm certain it's at the right point, I checked and doublechecked quite a few times. The link(s) I used to check were a bit fuzzy, like the tutorial here was pretty crappy photo wise (no offense. other then that it was great.) Anyone have a better picture?
Scratch that. Moved the D0 a tiny bit to the right.
Now I get the MS dash. The Xenium ICE LED is solid red, however.
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Wed May 04, 2005 10:20 pm Post subject:
Tried moving the D0 a few times, and it shuts off and shuts down again if it's not on the right spot. When it is, it just gives me the regular MS Dash. Bharosaihdoisa
Drago912 Xbox-HQ Member
Joined: Feb 15, 2005 Posts: 57 Location: Canada
Posted: Thu May 05, 2005 1:51 am Post subject:
Are you sure you have the chip plugged into the adapter properly?
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Fri May 06, 2005 3:40 am Post subject:
If I didn't, wouldn't the light not go on? I'm pretty certain... I'll play with it.
Still nothing. When the D0 isn't at the right spot, it doesn't work, so I 'm PRETTY SURE it's not the D0. Bad chip?
Drago912 Xbox-HQ Member
Joined: Feb 15, 2005 Posts: 57 Location: Canada
Posted: Fri May 06, 2005 8:53 pm Post subject:
Im not convinced its a bad chip.....can you take a picture of yer install and post it for us to see?
originalonen2002 Xbox-HQ Newbie
Joined: May 01, 2005 Posts: 4
Posted: Fri May 06, 2005 11:12 pm Post subject: Xenium Ice
I have that same chip and had many problems with the solderless adapter and soon as I got it soldered it worked perfectly after that except for trying to flash the bios of course separate issue but, for this issue thats the problem I had and got it fixed lol.......................
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Sat May 07, 2005 1:13 am Post subject:
Ugh, unfortunately I really don't have a picture. Every site I've looked at, the setup seems to be exactly what I have?
I'd consider having someone solder it for me, but I'm lazy.
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Wed May 11, 2005 2:03 am Post subject:
If you think you guys could help me if I grab a pic, I can do it soon... Also, I've got a second XBOX purchased as a gift that's modded, but I'll be damned if I can figure out where the modchip actually is installed.
TheModGod Xbox-Hq Legendary
Joined: Apr 18, 2004 Posts: 5303 Location: Greensburg PA
Posted: Wed May 11, 2005 8:39 pm Post subject:
You may have gotten a softmod or TSOP flashed machine.
If you cannot see the chip, it's either that or it's a SmartXX LT OPX chips soldered on the underside of hte motherboard. If you look to the left you can see the blue chip sticking out a little next to the side vent on the left side near the LPC area.
With your Xenium Ice issues... I am guessing it's the solderless adapter. They can be a bugger at times. _________________ Good Deals: Death@Hand, funkydopenloven, StaticMind, Slamscaper, PorscheXboxter
Bad Deals: None Yet
Pending Deals: Vanguard
Karranir Xbox-HQ Newbie
Joined: May 02, 2005 Posts: 9
Posted: Thu May 12, 2005 2:16 am Post subject:
Jah? I'll have someone solder it, I suppose. My father will be in town shortly, so I'll just have him do that...
As for the other XBOX, I've ANOTHER question: Let's say, hypothetically, that I... deleted the files on the hard-drive. Would this be repairable?
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum