HQ NETWORK:   XBOX ONE |  XBOX 360 |  AIDELUXE HQ Network: 2,719 | Guests: 1314 | Members: 9 


   Current Location: Forums Free Game Engine to develop games for XBOX360   |   XBOX-HQ T-Shirts, Hoodies, Mugs & More (Available Now)   |   The best new free XBOX ONE and XBOX ONE X games of 2019   |   Homebrew Xenium Modchip   |   Xbox 360-hq youtube channel now posting daily   |   List of Xbox One X Enhanced Games   |   Get the free XBOXONEHQ app for Android (1000+ Installs)   |   Road to 7000 Subs - XBOXONE-HQ.COM (XONEHQ) on YouTube   |   Games Coming to Xbox Game Pass For Console in September   |   HALO Xbox One X 4K HDR Update Out Now (MCC)   |   
  Home | Active Topics | CD/DVD Media | Downloads | Forums | Feedback | Games | HardDrives | Homebrew | My Profile | ModChips | Reviews | Search | SoftMods | Tutorials

Xbox Forums

Discuss all aspects of the original Xbox Console in our Interactive Xbox Forums..

Xbox-Hq.Com :: View topic - GD-ROM Laser Calibration Guide
Xbox-Hq.Com Forum Index -> SEGA Dreamcast Forums
Post new topic Reply to topic    
 GD-ROM Laser Calibration Guide View previous topic :: View next topic  
 
 
 
 
atreyu187
Xbox-HQ Enthusiast
Xbox-HQ Enthusiast


Joined: Apr 22, 2013
Posts: 21
Location: South Carolina

Post Posted: Sat May 11, 2013 3:51 am   
Post subject: GD-ROM Laser Calibration Guide
Reply with quote
 
To perform the laser recalibration, you'll need the following tools:
Phillips cross screwdriver, medium head size
small flat screwdriver or a small knife
Although not necessarily required, it's good to have an ohmmeter or oscilloscope. It's OK if you don't have one - operation can be done without it, but it's a bit riskier and more time consuming. A Chinese-made ohmmeter will work just fine, so head on to your local Chinese shop if you don't want to take chances.



Let's get to work.

Only four regular screws separate us from its internal components. To get to them, turn the console upside down.



Three corner screws can be seen directly, and the fourth one is hidden behind the modem, on the left side.



When the screws are loose, you can move the console to it's original position and lift the mask up. It should lift almost without any effort. You will see console's interior.



Laser lens will most likely be in the position marked on the picture, next to the disc spinning wheel. In order to reach the potentiometer which determines laser's intensity, you have to move the lens manually, as pictured below.


You'll hear a delicate cracking sound - the sound of a plastic gear moving against it's will. As long as you are gentle and don't overdo it, no harm will be done. When the laser is moved all the way, you can slowly lift the whole construction towards the right side, taking care of the flat cables.



You'll see the bottom side of the laser's mechanism. Right next to the flat cable is our potentiometer. It's probably sealed with red varnish to prevent it from moving. At this moment, it's very important to mark the starting position of potentiometer, so you can return to defaults if such need arises. You can do that by measuring the resistance with ohmmeter, or simply by marking the position with a soft pen.

It's important to measure the resistance before you start manipulating the potentiometer because different console models can have different starting values. You won't know how far you can safely go until you know the original resistance.

You'll need to decrease the potentiometers resistance (which results in increasing laser's power and disc reading ability). If you have an ohmmeter, decrease the resistance by a few ohms. If you do it manually, without a measuring device, simply turn the potentiometer clockwise (as shown) for about one degree, or, if you're unable to estimate it, just move it a very, very small bit Smile. If red varnish gets in our way, cut it with a thin scalpel.

After reducing the resistance, put the upper part of the laser back in its place (the lens doesn't need to be moved back this time, it will "park" itself once you turn the console on). It's time to try out your game disc. To do that, you can fully re-assemble the console, but it's also possible to do it in its current state. All you need is the game disc for testing, a power and video cables and a joypad. Before you turn the console on, find a way to permanently press the little switch on the upper right side of the device (possibly with a duct-tape), in order to fool the console that the disc lid is closed.

Keep in mind that operating with the opened, powered console can be dangerous for it, for you, and for your environment, therefore if you don't feel OK about it, assemble the console completely before you power it up.


Turn the console on, and try to start the game from disc. By noticing how much the console struggles while reading the disc you can approximate how far you are from calibrating the laser correctly.

Most likely the console won't load the game after the very first change of the potentiometer. That shouldn't discourage you because the process of laser calibration demands patience and precision. It's up to you to repeat reducing the resistance by a few ohms and testing the disc again. You should repeat this process until we you to a moment when the console successfully reads the disc. When that happens, try the same disc several times more, along with a few others games, to make sure the console loads all discs correctly. You might need to reduce the resistance one more time to assure reading in any situation.

If you're interested you can continue reducing the resistance and you'll notice that the quality of the disc reading, after passing a certain value, degrades again. So, there clearly is an optimal range of the resistances, generally different from console to console, where the laser successfully reads the discs, and out of which it reads them poorly, or not at all. That range changes over time as the console gets older and worn out.

A few important advices you should always keep in mind:
Decreasing of the potentiometer's resistance too much can burn the laser up. Generally, it's not advisable decreasing it more than 50 percent of the original value, but even that figure varies between consoles. If you have an ohmmeter, you can control the resistance. If you do it all manually, you have no means to determine when you're getting close to a dangerous value. Be aware of that.
Different types of discs reflect the light in different ways, and that determines required laser power for reading them. Before the calibration, it's good to decide what type of disc you'll use most of the time. Whether those are original discs or our personal backups, you should choose a type (in case of backups, many people consider Taiyo Yuden - pastel Verbatim CD-R a great choice), because the laser calibrated for one type of disc, will be inferior when reading from the other types.
Be patient and cautious. If you reduce the resistance in too big steps, you might completely miss the optimal disc reading range. So do it slowly, in small steps. Also, handle the console interior carefully and take care not to get laser lens more dirty than it already is
You can clean the laser with ear-cleaning cotton sticks soaked in alcohol. Several gentle, circular movements over the lens should be enough.
With a little bit of luck and a fair amount of patience, your Dreamcast can get a second life. If the calibration succeeds, appreciate the great gaming system you just fixed, and help other Dreamcast owners get their consoles up and running.


English Translation by Efendija


View user's profile Send private message
 
Display posts from previous:   
  Post new topic  
 
  Reply to topic  
|
 All times are GMT | Page 1 of 1
Jump to:  
 

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum
 

 Members Online (9) / Guests Online (1314)
Members Browsing
Chassidy29, DemetraBas, LowellMail, VanitaMoon, BarbAmm176, BufordBoel, KeeshaOver, RusselNrv, SueStarr98,

Legend
Administrator  Moderator  VIP Member  Registered User  Banned Users