Posted: Tue Aug 01, 2006 4:17 pm Post subject: need help with my dvd rom
I have a hard modded xbox(chip:aladdin no idea what version,software: evox 2.5 slayer auto installer) that works fine but lately the dvd rom hasnt been able to read any disks, or im getn the dirty disc error screen. So i bought a new phillips drive and i placed it into my xbox. The IDE cable and the yellow cable are secure but is there a flash that i can use so I dont have to re-modd my xbox with evox. I had a thompson and swithched to a philips, and my Thomspon was in my xbox at the time I moddded it. The error number on the top left of the screen is 08. I'm sure all cabbles are connected properly. But does this have to do any thing to re flashing my xbox or do i have to back every thing up then load evox again. The led on the middle of my xbox flashes green and red and i get the error meessage saying that i should send my xbox to customer support in green. I'm guessing i have to back every thing up from my xbox hdd to my pc. Then re-install evox and then dump every thing back to my xbox hdd. Is that what I have to do, If you have any idea what I'm doing wrong or suggestions to help me plz reply. THX for reading.
thepita23 Xbox-HQ Elite Member
Joined: Aug 06, 2004 Posts: 244
Posted: Tue Aug 01, 2006 4:37 pm Post subject: reply
make sure your hard drive is set to cable select and that the ide and power cable are connected all of the way. You dont have to reflash a chip when u change the dvd drive. Also error code 8 - kernel - No HDD found
Joined: May 06, 2006 Posts: 1155 Location: Philly, PA
Posted: Tue Aug 01, 2006 4:47 pm Post subject:
Yup you could have kicked the cable lose off the HDD swaping out your DVD _________________ The mighty V6 Passat came to chew bubble gum and kick%^* and shes all out of bubble gum!
Greven Xbox-Hq Genius Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Jan 19, 2006 Posts: 2755 Location: Calgary, Alberta, Canada
Posted: Tue Aug 01, 2006 6:31 pm Post subject:
I find it odd that it didn't give you a 07, which is what typically happens when the hdd cannot be contacted.
I've had an 8 error before, and what had happened was the partition table had become corrupt, and I ended up having to format and reinstall everything. _________________ Hotswap|HDD Upgrade|X3 Guide
jokaankit Xbox-HQ Newbie Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Aug 01, 2006 Posts: 6
Posted: Tue Aug 01, 2006 11:07 pm Post subject: my new dvd rom is still not working
Let my start of by thanking every 1 that cared and replied. All my cable are as secure as can be. When i place my thompson drive my xbox works fine, when i put my new philips the xbox logo starts up then error number 08 comes up.If any 1 has any idea whats going on or any suggestions I would appretiate it. THX
Greven Xbox-Hq Genius Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Jan 19, 2006 Posts: 2755 Location: Calgary, Alberta, Canada
Posted: Wed Aug 02, 2006 12:32 am Post subject:
Ouch. Sounds like that drive might be defective and isn't allowing and communication past that point in the cable.
I double checked with a buddy from work that was a computer tech, and if the master device on an IDE cable isn't working,it can cause the slace device to not be detected.
I would say that the drive is pooched, may want to get a second opinion though _________________ Hotswap|HDD Upgrade|X3 Guide
jokaankit Xbox-HQ Newbie Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Aug 01, 2006 Posts: 6
Posted: Wed Aug 02, 2006 3:40 pm Post subject: dvd rom problems
Dude thanks for really careing dude. I was woundering I dont think that the dvd rom is defective b/c its factory sealed and the mptor eject works perfectley fine. I agree with what your friend said its obviously something to do with iether drive not being capable to transfer data to my hdd or I need to upgrade my IDE cable with 1 thats faster maybe. My main concerne was the posability of having to reinsall evox on my xbox. <------------------------can you make sure thats not the case b/c my cousin had installed it for me n I dont want to do anything wrong.
jokaankit Xbox-HQ Newbie Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Aug 01, 2006 Posts: 6
Posted: Wed Aug 02, 2006 10:48 pm Post subject: DVD ROM
You have a duff philips drive..It's also possible you have dislodged the chip when changing drives. Try the tommy again and see if you get a normal boot, if so then if you feel brave try adjusting the laser.
There isn't any point messing with the philips drive. It's a failed board..Get your money back on it.
Just for info.. Llamma has a sale on with the Samsung dvd drive at $59
THIS IS WHAT SOM1 REPLIED TO ME ON ANOTHER FORUM CAN THIS BE THE CASE OR IS HE WRONG, IF SO HOW DO I LOCK MY HDD. THX
Greven Xbox-Hq Genius Xbox Version: Xbox V1.6 Modded: Xecuter 3 CE
Joined: Jan 19, 2006 Posts: 2755 Location: Calgary, Alberta, Canada
Posted: Thu Aug 03, 2006 4:03 am Post subject:
Like I said, I think the one is dead, and you might be better off trying to fix the original. Those are good tutorials, and can't hurt on the old drive.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 8,699 | 
Guests: 1237 | 
Members: 0 
Forums 
