Posted: Fri Sep 10, 2004 4:50 am Post subject: PLEASE!! Aladdin Live !! SOMEONE !!!! Orange and Red Flash!!
Hi,
i receive in last week the aladdin Live chip and my new Xbox Halo Edition v1.6....... But i instaled the modchip - Uhappyness - don't work....... The Led is orange, boot, and red orange flash lights.
I flash my modchip with programer, but something is wrong, because in the verificatin mode should the Error 0x0000.......... And the problens continue............ If i remove the Bt and L1, the led flash Red and Green....
I check all points, everything is ok..... all points is right.
The prograns and flash i take in Aladdinlive.com......
Please, i need a big help!!!!!!!!!!!!!!
Sorry for my bad english, in live in Brazil, Xboxbrazilian......
I'm not that familar with that modd chip.... when u checked your solder points and saw that they are correct, did u check to make sure u did not splatter any solder and are not coming in contact with other leads. Also, hope u didnt get the points on the main board too hot cause the heat can transfer to sensitive chips else where causing damage.....Examine your mainboard carefully until someone more familar with that chip can help u....
Take it easy.....In Brazil.......
Glauco74 Xbox-HQ Newbie
Joined: Aug 13, 2004 Posts: 4 Location: Brazil
Posted: Fri Sep 10, 2004 7:32 am Post subject:
Yeah,
i check the points, not splash any solder, because i not use solder in motherboard, only conect the wires to test..............
Check the site again.... only problem is in the flash the ChipBios, verify error......... small process, write all block, but in verification, error Ec00x1, or another address........
Check with multimeter........ all wires has conected.......... the led of chip turn-on - purple..........
I remove the chip and the Xbox works ok. Put the chip again and the problem come back, i try 2 chip....... solder de programer, flash the bios........ and not resolve.......
My only anwser is, RED - GREEN (if L1 and BT not conect) or Orange - Red (if L1 and BT conect)..................
My next step - buy a Shotgun........
Sorry again for my bad and trash english....
Xbox - Brazilians - Clan.
dckillah Xbox-HQ User
Joined: Aug 27, 2004 Posts: 13
Posted: Sat Sep 11, 2004 1:58 am Post subject:
Same exact problem happened to me....let me tell you wut i had to do....
when u flash it with the 1.6 bios from aladding or evox you get the 0x00000 when verifying. this is wut i did to solve that FLASH IT WITH THE 1.5 BIOS FOUND IN THE ALADDING LIVE WEBSITE...then re-flash it with the 1.6 evox bios; it'll go through with no problem.
ALSO when i first installed my chip i was following this picture Notice that the chip is being soldered through the left end of the chip...that's WRONG!!!!!!! (big headache this gave me) Where you see it labeled [flash] on the chip there should be the pin holes that connect to the external flasher; simply plug that into the pins that you soldered to the motherboard, the chip itself is not soldered to the MoBo. BT HAS to be soldered from the MoBo to the Chip and GROUND the D0 point.
if you have any questions just let me know; and post pics if you can so i can diagnose; but if you follow wut i told you it should work
Glauco74 Xbox-HQ Newbie
Joined: Aug 13, 2004 Posts: 4 Location: Brazil
Posted: Sat Sep 11, 2004 8:26 am Post subject:
Thanks a lot.......... Everybody........
I not conet the pin 1 and 2....... Maybe it's wrong......... I conect only four points in aladdin site. But i will fallow your instruction.
The error in flash chip appear again...... In Executer 2.......... Verify Error 0x000000
I try install the chip in 1.5 Mo Bo, but don't work too. The xbox start in normal mode, not recognize CDRW, the light of chip is on. But, nothing happens. I will remove the Mo Bo and check the point D0.
I use the same cable to conect D0, Ground, Mobo, make three point in cable. it's right???
I will post the pictures of Mo Bo and chip instaled.....
Anyway, i have a 2 blocked Xbox and a Biiiiiiiig problem...... Now, i Go to the beach, see a somegirls, relex the mind, drink one bear, and come back to work..........
Thanks again to everybody....
dckillah Xbox-HQ User
Joined: Aug 27, 2004 Posts: 13
Posted: Sat Sep 11, 2004 4:58 pm Post subject:
just connect the D0 from motherboard to Ground; leave it blank on the chip
Glauco74 Xbox-HQ Newbie
Joined: Aug 13, 2004 Posts: 4 Location: Brazil
Posted: Mon Sep 13, 2004 4:43 pm Post subject:
Hehehehe
Everybody,
everythink is ok in my Xbox, i use the picture conect all LPC points ( more BT, L1 and D0 to Ground and Motherboard.
Not conect L2 and Flash the Chip.
Work in my 1.5 and 1.6 versions of Xbox.
I send pictures later.............
Thanks a lot.........
rymon Xbox-HQ Newbie
Joined: Nov 20, 2004 Posts: 1
Posted: Sat Nov 20, 2004 6:23 am Post subject: Aladdin install step by step
Could someone post a step by step for the Aladdin Live? I've been following various directions on the net but noone is all that clear, and I can't seem to get it to work.
Once the XBox is disassembled, here is what I've ascertained I should do:
Insteall LPC Header PIN assembly, and solder from bottom of MB.
Push chip down onto PINs on top of MB.
Solder wires between spots on Chip and MB, except for D0 which gets soldered to ground.
Does this sound right? I'm just getting the orange/green flashing.
Any help much appreciated.
Thanks,
R
custom-xmodz Xbox-HQ Freak
Joined: Aug 28, 2004 Posts: 796 Location: Wales, UK
Posted: Mon Nov 22, 2004 10:19 pm Post subject:
Ok, the aladdin live is real simple.
Solder the LPC header to the MOBO, plug the chip into the header (or solde rit) solder the D0 on the chip to the D0 on the board, and the BT on the chip to the BT on the board, (if you ground either it will be in modded mode all the time, and won't work on some aladdins)
Also if you have a 1.5 or a 1.6 version xbox then the LPC bus is not fully connected and you need to do an LPC fix which is a lot more involved on a 1.6, it won't work unless you do this.
I have the external flasher but have never need to program the chip to get it working, tho I flash via evox to update it.
DJH
|
All times are GMT |Page 1 of 1
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
HQ Network: 8,029 | 
Guests: 996 | 
Members: 2 
Forums 
Notice that the chip is being soldered 
more BT, L1 and D0 to Ground and Motherboard.
